分享到:

东莞华钛制冷设备科技有限公司华钛制冷,用户至上,信誉第一!

联系资料

东莞华钛制冷设备科技有限公司
所在地区:
广东省 东莞市
公司主页:
暂无
电话号码:
0769*******
传真号码:
暂无
联 系 人:
韩经理
移动电话:
1345*******
电子邮箱:
暂无

最新信息

查看更多>

广州市环保空调生产厂家带你了解冷风机的安装技术要求

发布于:2015年10月12日 来源:www.szfuhai.com
[摘要]广州市环保空调生产厂家,专业生产环保空调、各种风机,面向车间、工厂、酒店等地进行施工降温工程,欢迎来电咨询

广州市环保空调生产厂家带你了解冷风机的安装技术要求

 

 

    介绍冷风机的安装技术要求:
  要求1、采用40*40*4角铁架与墙或窗板螺栓连接;
  要求2、所有缝隙均用玻璃胶与水泥沙密封;
  要求3、送风管的截面积要求不能小于0.45平方米;
  要求4、安装三角支架焊接和安装一定要牢固;
  要求5、安装支架与主机必须水平;
  要求6、所有外墙风管部位要做好防水处理;
  要求7、主机底部与支架接触部分须垫防震垫;
  要求8、锌铁瓦棚上安装要有足够的强度,能承受环保空调主机的重量;
  要求9、屋顶或屋面开口尺寸应不大于风管尺寸20mm,否则做不好防水处理;
  要求10、在安装不同位置要留有足够的进风量及维修位;
  要求11、进墙或进窗子风管根据使用场所确定尺寸截面积,但不能小于0.45平方米;
  要求12、遥控器接收盒连接通信线从出风管引入室内,安装在易于接收遥控信号的位置,须在出风管上开出22mm的孔,固定在室内适当的位置。

      生产厂家,专业生产环保空调、各种风机,面向车间、工厂、酒店等地进行施工降温工程,欢迎来电咨询

     

 

  Technical requirements for the installation of air cooling machine for the production of environmental protection air conditioner:
  1, using the 40*40*4 angle iron frame and the walls or shutters bolt connection;
  Requirements 2, all the cracks are made of glass and cement sand seal;
  Request 3, the environmental protection air conditioning delivers the wind pipe the cross-sectional area request cannot be less than 0.45 square meters;
  Requires 4, the installation of triangular frame welding and installation must be strong;
  Requirements 5, the installation of the stent and the host must level;
  Requires 6, all external wall of the wind pipe site to do a good job of water treatment;
  Request 7, the main engine bottom and the contact part of the bracket to pad pad;
  8, he shed on the installation of zinc must have enough strength, can bear the weight of environmental protection air conditioning unit;
  Requirements 9, roof or roof opening size should not be greater than the size of the wind pipe 20mm, otherwise do not do good waterproof processing;
  Requires 10, in the installation of different position to stay with enough air into the air and maintenance;
  Request 11, into the wall or into the window of the wind pipe according to the use of the location to determine the size of the cross-sectional area, but can not be less than 0.45 square meters;
  Request 12, remote control receiver box to connect the communication line from the air duct into the room, installed in the remote control signal is easy to receive the location of the 22mm hole, fixed in the indoor appropriate location.
  Guangzhou City, environmental protection and air conditioning manufacturers, professional production of environmental protection, air conditioners, all kinds of fans, for the workshop, factories, hotels and other places to carry out the construction cooling project, welcome to inquire